The Haws 7501 Cfg STD-9083 compact portable eyewash is a 9-gallon (34.1 L) capacity gravity operated portable eyewash that supplies a continuous flow of water for a full 15 minutes at .4 gpm. This unit is a cost-effective solution ideal for locations without access to potable water, including temporary decontamination sites, temporary treatment facilities, and short-term job sites. The 9083 cleansing stick provides clean water and ANSI compliance in equipment up to 15 gallons (60 L) for up to three years when serviced just once annually.
- Featuring a FDA approved high-density green polyethylene tank that is easily activated by pulling the yellow activation arm down to the open position
- A wide-fill opening with a securely threaded cap, and a pronounced ‘Max Fill’ line permits easy inspection, cleaning and filling
- Relocation is simple due to ‘Lift Here’ graphics, easily mounted bracket (included) and light design of this 9-gallon (34.1 L) portable
- Measurements: 14-1/2″ high, 22″ wide, 10-1/8″ (36.8 x 55.9 x 25.7 cm) deep. *Note: Unit must be wall hung
Certified by CSA to meet the ANSI/ISEA Z358.1 Standard for Emergency Eyewash and Shower Equipment.
1011HS – Haws RIVIVEâ„¢ Hydration Stationâ„¢ Recessed Bottle Filler with HI-LO FountainsModel | 1011HS |
Material | 14-gauge Type 304 Stainless Steel fountain brackets with the remainder of unit 18-gauge in a satin finish |
Features |
Vandal Resistant
Programable
Auto purge feature automatically cycles once every 24 hours
|
Dimensions |
Length: 18-5/8″
Width: 38-1/4″
Height: 28-3/8″
|
ADA | Yes |
Hygienic Features |
24-Hour Purge of water line
Sensor Operated Bottle Filler
100% lead-free waterways
|
Field Configurable Filtering | Choose between filtered or non-filtered water with the included interchangeable 3000-gallon filter and 5y rated strainer. |
Included Components |
Bottle Filler and Fountains
Mounting Frame
Interchangeable filter and strainer
|
Power | <1 Amp |
Code Compliance |
ADA
NSF/ANSI/CAN 61- Section 9
CSA Certified
NSF/ANSI/CAN 372
California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100)
NSF/ANSI/CAN 61: Q ≤ 1
|
Mounting | Wall Mounted (In-Wall Frame Included) |
Model 1011HS barrier-free vandal-resistant drinking fountain and motion-activated bottle filling station uses a patented stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. Outfitted with such protective features as vandal-resistant bubbler heads, waste strainers, and bottom plates, this electric water cooler is quick to discourage vandals.
- The fountains stainless steel valve body is the only one on the market machined from solid bar stock
- 18-gauge Type 304 Stainless Steel bowl assemblies mounted on 14-gauge Type 304 Stainless Steel wall brackets
- Vandal resistant components include the bubblers, bowls, buttons, drains and bottom plates
- Engineered waste plumbing with enough access room for water stop, electrical junction box, filter and drain connections (requires rear access)
- LED lighted 12″ sensor operated bottle opening with quick 1.1 gpm fill rate and laminar flow with front access for changing filter
- 3000 gallon (11356 L) capacity, Electronic Lifecycle Control filter cartridge, with filter replacement indicator light. When filter expires, solenoid stops dispensing water to bottle filler
- Auto purge feature automatically cycles once every 24 hours, if no use, to assure a fresh water supply as well as trap integrity
- 100% lead-free waterways
- Display menu which shows sensor range adjustment, factory reset, software/firmware version readout and error readout, along with bottle counter showing number of bottles saved
- Vandal-resistant sensor resists scratching and water droplet fowling, and is separated from display for maintenance
- Easy maintenance with front fountain access to valve adjustment and cartridge replacement
Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.
1001HS – Haws RIVIVEâ„¢ Hydration Stationâ„¢ Recessed Bottle Filler Station with FountainModel | 1001HS |
Material | Â 14-gauge Type 304 Stainless Steel fountain bracket with the remainder of unit 18-gauge in a satin finish |
Features |
Vandal Resistant
Programable
Auto purge feature automatically cycles once every 24 hours
|
Dimensions |
Length: 18-5/8″
Width: 19-5/8″
Height: 28-3/8″
|
ADA | Yes |
Hygienic Features |
24-Hour Purge of water line
Sensor Operated Bottle Filler
100% lead-free waterways
|
Field Configurable Filtering | Choose between filtered or non-filtered water with the included interchangeable 3000-gallon filter and 5y rated strainer. |
Included Components |
Bottle Filler and Fountain
Mounting Frame
Interchangeable filter and strainer
|
Power | <1 Amp |
Code Compliance |
ADA
NSF/ANSI/CAN 61- Section 9
CSA Certified
NSF/ANSI/CAN 372
California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100)
NSF/ANSI/CAN 61: Q ≤ 1
|
Mounting | Wall Mounted (In-Wall Frame Included) |
Model 1001HS barrier-free vandal-resistant drinking fountain and motion-activated bottle filling station offers the only all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. Outfitted with such protective features as a vandal-resistant bubbler head, waste strainer, and bottom plates, this fountain is quick to discourage vandals.
- The fountains stainless steel valve body is the only one on the market machined from solid bar stock
- 18-gauge Type 304 Stainless Steel bowl assembly mounted on a 14-gauge Type 304 Stainless Steel wall bracket
- Vandal resistant components include the bubbler, bowl, button, drain and bottom plate
- Engineered waste plumbing with enough access room for water stop, electrical junction box, filter and drain connections (rear access is required)
- LED lighted 12″ sensor operated bottle filler opening with quick 1.1 gpm fill rate and laminar flow with front access for changing filter
- 3000 gallon (11356 L) capacity, Electronic Lifecycle Control filter cartridge, with filter replacement indicator light. When filter expires, solenoid stops dispensing water to bottle filler
- Auto purge feature automatically cycles once every 24 hours, if no use, to assure a fresh water supply as well as trap integrity
- 100% lead-free waterways
- Display menu which shows sensor range adjustment, factory reset, software/firmware version readout and error readout, along with bottle counter showing number of bottles saved
- Vandal-resistant sensor resists scratching and water droplet fowling, and is separated from display for maintenance
- Easy maintenance with front fountain access to filter, valve adjustment and cartridge replacement
Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.
H1117.8-1920HO – ADA Vandal-Resistant Chilled Adjustable Drinking Fountain and Motion-Activated Bottle FillerModel H1117.8-1920HO ADA vandal-resistant electric water cooler and motion-activated bottle filler provides 8 gph (30.3 L) chilled water performance in an engineered stainless steel skin. This wall-mounted low profile bowl designed fountain offers the only all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve.
- Optional 3000 gallon water filter available (model 6480)
- Only stainless steel valve body that is machined out of solid bar stock
- Touchless operation on the bottle filler for safety and peace of mind
- 100% Lead free waterways. 14-gauge Type 304 Stainless Steel construction and required specialized mounting frame offer a well constructed sturdy fountain
- Vandal resistant components include the bubblers, buttons, drains and bottom plates
- Maintenance is made easy with front access to valve adjustment and cartridge replacement
- Grille slots are designed to eliminate sharp edges and are backed with a foam filter to protect the fan motor and high displacement compressor from debris
- 1 gpm (3.78 L) bottle filler laminar flow
- Designed to run at a low energy usage, this water cooler is assured to have a long-lasting life
- One piece rectangular fountain bowl is designed for extra durability and maintenance ease
- Beautiful satin finish resists stains and corrosion
Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.
Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.
2000HSSM – Haws RIVIVEâ„¢ Hydration Stationâ„¢ Surface Mount Bottle FillerModel | 2000HSSM |
Material | 16-gauge Type 304 Stainless Steel – Satin Finish |
Features |
Vandal Resistant
Front access maintenance and filter change
Programable
Auto purge feature automatically cycles once every 24 hours
|
Dimensions |
Length: 1″
Width: 17-1/4″
Height: 30-3/4″
|
ADA | Yes |
Hygienic Features |
24-Hour Purge of water line
Sensor Operated Bottle Filler
100% lead-free waterways
|
Field Configurable Filtering | Choose between filtered or non-filtered water with the included interchangeable 3000-gallon filter and 5y rated strainer. |
Included Components |
Bottle Filler
Mounting Can
Interchangeable filter and strainer
|
Fill Rate | 1.2 |
Power | <1 Amp |
Code Compliance |
ADA
NSF/ANSI/CAN 61- Section 9
CSA Certified
NSF/ANSI/CAN 372
California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100)
NSF/ANSI/CAN 61: Q ≤ 1
|
Mounting | Wall Mounted (On-wall mounting can) |
The model 2000HSSM surface mounted, architectural bottle filling station is a vandal-resistant, motion-activated water dispenser with architectural appeal that allows users to enjoy the benefits of fresh, filtered water with none of the drawbacks of bottled water. Surface mounted design allows the bottle filling station to be placed securely in multiple locations without taking up excess space, allowing for use in high-traffic applications such as schools, office buildings, fitness centers, and manufacturing facilities.
- Tested and certified by CSA against NSF/ANSI/CAN 61, Section 9, NSF/ANSI/CAN 372, CSA Standard B483.1 and California Health and Safety Code 116875 (AB 1953-2006)
- All stainless-steel front panels and bottle filler alcove
- Sensor features a 20-second timeout function which prevents unwanted use
- Auto purge feature automatically cycles once every 24 hours to assure a fresh water supply as well as trap integrity
- State-of-the-art integral water filtration system assures fresh, filtered water
- 3000 gallon (11356 L) capacity, with filter replacement indicator light to notify when replacement is necessary, model 6428
- Front access for changing smart filter which incorporates easy set, change and monitor reset programming
- Laminar flow prevents splashing, keeping the drinking area contained and clean
- Large LED lit 12″ bottle opening with quick 1.1 gpm fill rate, and bottle counter showing number of bottles saved
- Field-configurable as either filtered or non-filtered
- Intended for indoor use only
Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61, Section 9, NSF/ANSI/CAN 372, and CSA Standard B483.1. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), California Proposition 65 and the Federal Safe Drinking Water Act.
2000HSA.8 – Haws RIVIVEâ„¢ Hydration Stationâ„¢ Chilled Recessed Bottle FillerModel | 2000HSA.8 |
Material | 16-gauge Type 304 Stainless Steel – Satin Finish |
Features |
Vandal Resistant
Front access maintenance and filter change
Programable
Smart Energy Savings Mode
Auto purge feature automatically cycles once every 24 hours
|
Dimensions |
Length: 18-5/8″
Width: 19-5/8″
Height: 50″
|
ADA | Yes |
Hygienic Features |
24-Hour Purge of water line
Sensor Operated Bottle Filler
100% lead-free waterways
|
Field Configurable Filtering | Choose between filtered or non-filtered water with the included interchangeable 3000-gallon filter and 5y rated strainer. |
Included Components |
Chiller (HCR8)
Bottle Filler
Mounting Frame
Interchangeable filter and strainer
|
Chilling | Refrigeration system is hermetically sealed and delivers a minimum of 8 gph (30.3 L) of water at 50° F (10° C) cooled from 80° F (26.7° C) inlet water at 90° F (32.2° C) ambient. |
Power | 115 Volts, 60Hz, rated watts: 370, full load amps: 5 |
Code Compliance |
ADA
NSF/ANSI/CAN 61- Section 9
CSA Certified
NSF/ANSI/CAN 372
California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100)
NSF/ANSI/CAN 61: Q ≤ 1
|
Mounting | Wall Mounted (In-Wall Frame Included) |
The model 2000HSA.8 vandal-resistant, Architectural, chilled, motion-activated bottle filling station is a touch-free, hygienic, water dispenser with architectural appeal that allows users to enjoy the benefits of fresh, filtered water with none of the drawbacks of bottled water. Recessed, in-wall-mounted design allows the bottle filling station to be placed securely in multiple locations without taking up excess space, and is practical for permanent, high-traffic applications such as schools, office buildings, fitness centers, and manufacturing facilities.
- Tested and certified by CSA against NSF/ANSI/CAN 61, Section 9, NSF/ANSI/CAN 372, CSA Standard B483.1 and California Health and Safety Code 116875 (AB 1953-2006)
- All stainless-steel front panels and bottle filler alcove
- Sensor features a 20-second timeout function which prevents unwanted use
- Auto purge feature automatically cycles once every 24 hours to assure a fresh water supply as well as trap integrity
- State-of-the-art integral water filtration system assures fresh, filtered water
- 3000 gallon (11356 L) capacity, with filter replacement indicator light to notify when replacement is necessary, model 6428
- Smart energy savings feature powers down refrigeration system after 2 hours of non-use and will automatically start again when used
- Front access for changing smart filter which incorporates easy set, change and monitor reset programming
- Laminar flow prevents splashing, keeping the drinking area contained and clean
- Large LED lit 12″ bottle opening with quick 1.1 gpm fill rate, and bottle counter showing number of bottles saved
- Field-configurable as either filtered or non-filtered
- Intended for indoor use only
Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”. Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.
2000HS – Haws RIVIVEâ„¢ Hydration Stationâ„¢ Recessed Bottle FillerModel | 2000HS |
Material | 16-gauge Type 304 Stainless Steel – Satin Finish |
Features |
Vandal Resistant
Front access maintenance and filter change
Programable
Auto purge feature automatically cycles once every 24 hours
|
Dimensions |
Length: 1″
Width: 17-1/4″
Height: 30-3/4″
|
ADA | Yes |
Hygienic Features |
24-Hour Purge of water line
Sensor Operated Bottle Filler
100% lead-free waterways
|
Field Configurable Filtering | Choose between filtered or non-filtered water with the included interchangeable 3000-gallon filter and 5y rated strainer. |
Included Components |
Bottle Filler
Mounting Frame
Interchangeable filter and strainer
|
Fill Rate | 1.2 |
Power | <1 Amp |
Code Compliance |
ADA
NSF/ANSI/CAN 61- Section 9
CSA Certified
NSF/ANSI/CAN 372
California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100)
NSF/ANSI/CAN 61: Q ≤ 1
|
Mounting | Wall Mounted (In-Wall Frame Included) |
The model 2000HS vandal-resistant, Architectural, motion-activated bottle filling station is a touch-free, hygienic, water dispenser with architectural appeal that allows users to enjoy the benefits of fresh, filtered water with none of the drawbacks of bottled water. Recessed, in-wall-mounted design allows the bottle filling station to be placed securely in multiple locations without taking up excess space. The unit conveniently mounts between standard 16″ (406 mm) studs and is practical for permanent, high-traffic applications such as schools, office buildings, fitness centers, and manufacturing facilities.
- Tested and certified by CSA against NSF/ANSI/CAN 61, Section 9, NSF/ANSI/CAN 372, CSA Standard B483.1 and California Health and Safety Code 116875 (AB 1953-2006)
- All stainless-steel front panels and bottle filler alcove
- Sensor features a 20-second timeout function which prevents unwanted use
- Auto purge feature automatically cycles once every 24 hours to assure a fresh water supply as well as trap integrity
- State-of-the-art integral water filtration system assures fresh, filtered water
- 3000 gallon (11356 L) capacity, with filter replacement indicator light to notify when replacement is necessary, model 6428
- Front access for changing smart filter which incorporates easy set, change and monitor reset programming
- Laminar flow prevents splashing, keeping the drinking area contained and clean
- Large LED lit 12″ bottle opening with quick 1.1 gpm fill rate, and bottle counter showing number of bottles saved
- Field-configurable as either filtered or non-filtered
- Intended for indoor use only
Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61, Section 9, NSF/ANSI/CAN 372, and CSA Standard B483.1. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), California Proposition 65 and the Federal Safe Drinking Water Act.
1001HSA – Haws RIVIVEâ„¢ Hydration Stationâ„¢ Recessed Bottle Filler with FountainModel | 1001HSA |
Material | 14-gauge Type 304 Stainless Steel fountain bracket with the remainder of unit 18-gauge in a satin finish |
Features |
Vandal Resistant
Front access maintenance and filter change
Programable
Auto purge feature automatically cycles once every 24 hours
|
Dimensions |
Length: 18-5/8″
Width: 19-5/8″
Height: 50″
|
ADA | Yes |
Hygienic Features |
24-Hour Purge of water line
Sensor Operated Bottle Filler
100% lead-free waterways
|
Field Configurable Filtering | Choose between filtered or non-filtered water with the included interchangeable 3000-gallon filter and 5y rated strainer. |
Included Components |
Bottle Filler and Fountain
Mounting Frame
Interchangeable filter and strainer
|
Power | <1 Amp |
Code Compliance |
ADA
NSF/ANSI/CAN 61- Section 9
CSA Certified
NSF/ANSI/CAN 372
California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100)
NSF/ANSI/CAN 61: Q ≤ 1
|
Mounting | Wall Mounted (In-Wall Frame Included) |
Model 1001HSA barrier-free vandal-resistant drinking fountain and bottle filling station offers the only all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. Outfitted with such protective features as a vandal-resistant bubbler head, waste strainer, and bottom plates, this fountain is quick to discourage vandals. Fountain and bottle filler advantages include:
- The fountains stainless steel valve body is the only one on the market machined from solid bar stock
- 18-gauge Type 304 Stainless Steel bowl assembly mounted on a 14-gauge Type 304 Stainless Steel wall bracket
- Vandal resistant components include the bubbler, bowl, button, drain and bottom plate
- Front access engineered waste plumbing with enough access room for water stop, electrical junction box, filter and drain connections
- LED lighted 12″ sensor operated bottle filler opening with quick 1.1 gpm fill rate and laminar flow with front access for changing filter
- 3000 gallon (11356 L) capacity, Electronic Lifecycle Control filter cartridge, with filter replacement indicator light. When filter expires, solenoid stops dispensing water to bottle filler
- Auto purge feature automatically cycles once every 24 hours, if no use, to assure a fresh water supply as well as trap integrity
- 100% lead-free waterways
- Display menu which shows sensor range adjustment, factory reset, software/firmware version readout and error readout, along with bottle counter showing number of bottles saved
- Vandal-resistant sensor resists scratching and water droplet fowling, and is separated from display for maintenance
- Easy maintenance with front fountain access to valve adjustment and cartridge replacement
Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.
1011HSA – Haws RIVIVEâ„¢ Hydration Stationâ„¢ Recessed Bottle Filler with HI-LO Fountains
Model | 1011HSA |
Material | 14-gauge Type 304 Stainless Steel fountain bracket with the remainder of unit 16-gauge in a satin finish |
Features |
Vandal Resistant
Front access maintenance and filter change
Programable
Auto purge feature automatically cycles once every 24 hours
|
Dimensions |
Length: 18-5/8″
Width: 38-1/4″
Height: 50″
|
ADA | Yes |
Hygienic Features |
24-Hour Purge of water line
Sensor Operated Bottle Filler
100% lead-free waterways
|
Field Configurable Filtering | Choose between filtered or non-filtered water with the included interchangeable 3000-gallon filter and 5y rated strainer. |
Included Components |
Bottle Filler and Fountains
Mounting Frame
Interchangeable filter and strainer
|
Power | <1 Amp |
Code Compliance |
ADA
NSF/ANSI/CAN 61- Section 9
CSA Certified
NSF/ANSI/CAN 372
California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100)
NSF/ANSI/CAN 61: Q ≤ 1
|
Mounting | Wall Mounted (In-Wall Frame Included) |
Model 1011HSA barrier-free vandal-resistant drinking fountain and motion-activated bottle filling station uses a patented stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. Outfitted with such protective features as vandal-resistant bubbler heads, waste strainers, and bottom plates, this electric water cooler is quick to discourage vandals.
- The fountains stainless steel valve body is the only one on the market machined from solid bar stock
- 18-gauge Type 304 Stainless Steel bowl assemblies mounted on 14-gauge Type 304 Stainless Steel wall brackets
- Vandal resistant components include the bubblers, bowls, buttons, drains and bottom plates
- Front access engineered waste plumbing with enough access room for water stop, electrical junction box, filter and drain connections
- LED lighted 12″ sensor operated bottle opening with quick 1.1 gpm fill rate and laminar flow with front access for changing filter
- 3000 gallon (11356 L) capacity, Electronic Lifecycle Control filter cartridge, with filter replacement indicator light. When filter expires, solenoid stops dispensing water to bottle filler
- Auto purge feature automatically cycles once every 24 hours, if no use, to assure a fresh water supply as well as trap integrity
- 100% lead-free waterways
- Display menu which shows sensor range adjustment, factory reset, software/firmware version readout and error readout, along with bottle counter showing number of bottles saved
- Vandal-resistant sensor resists scratching and water droplet fowling, and is separated from display for maintenance
- Easy maintenance with front fountain access to valve adjustment and cartridge replacement
Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.
1001HSA.8 – Haws RIVIVEâ„¢ Hydration Stationâ„¢ Chilled Recessed Bottle Filler with Fountain
Model | 1001HSA.8 |
Material | 14-gauge Type 304 Stainless Steel fountain bracket with the remainder of unit 18-gauge in a satin finish |
Features |
Vandal Resistant
Front access maintenance and filter change
Smart Energy Savings Mode
Programable
Auto purge feature automatically cycles once every 24 hours
|
Dimensions |
Length: 18-5/8″
Width: 19-5/8″
Height: 50″
|
ADA | Yes |
Hygienic Features |
24-Hour Purge of water line
Sensor Operated Bottle Filler
100% lead-free waterways
|
Field Configurable Filtering | Choose between filtered or non-filtered drinking water with the included interchangeable 3000-gallon filter and 5y rated strainer. |
Included Components |
Chiller (HCR8)
Bottle Filler and Fountain
Mounting Frame
Interchangeable filter and strainer
|
Chilling | Refrigeration system is hermetically sealed and delivers a minimum of 8 gph (30.3 L) of water at 50° F (10° C) cooled from 80° F (26.7° C) inlet water at 90° F (32.2° C) ambient. |
Power | 115 Volts, 60Hz, rated watts: 370, full load amps: 5 |
Code Compliance |
ADA
NSF/ANSI/CAN 61- Section 9
CSA Certified
NSF/ANSI/CAN 372
California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100)
NSF/ANSI/CAN 61: Q ≤ 1
|
Mounting | Wall Mounted (In-Wall Frame Included) |
Model 1001HSA.8 barrier-free vandal-resistant electric water cooler and bottle filling station provides 8 gph (30.3 L) chilled drinking water performance in an engineered stainless steel skin. This wall-mounted swirl bowl designed fountain offers the only all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. Outfitted with such protective features as a vandal-resistant bubbler head, waste strainer, and bottom plates, this electric water cooler is quick to discourage vandals. Fountain and bottle filler advantages include:
- The fountains stainless steel valve body is the only one on the market machined from solid bar stock
- 18-gauge Type 304 Stainless Steel bowl assembly mounted on a 14-gauge Type 304 Stainless Steel wall bracket
- Vandal resistant components include the bubbler, bowl, button, drain and bottom plate
- Front access engineered waste plumbing with enough access room for water stop, electrical junction box, filter and drain connections
- LED lighted 12″ sensor operated bottle opening with quick 1.1 gpm fill rate and laminar flow with front access for changing filter
- 3000 gallon (11356 L) capacity, Electronic Lifecycle Control filter cartridge, with filter replacement indicator light. When filter expires, solenoid stops dispensing water to bottle filler
- Smart energy savings feature powers down refrigeration system after 2 hours of non-use and will automatically start again when used
- Auto purge feature automatically cycles once every 24 hours, if no use, to assure a fresh water supply as well as trap integrity
- 100% lead-free waterways
- Display menu which shows sensor range adjustment, factory reset, software/firmware version readout and error readout, along with bottle counter showing number of bottles saved
- Vandal-resistant sensor resists scratching and water droplet fowling, and is separated from display for maintenance.
- Easy maintenance with front fountain access to valve adjustment and cartridge replacement
Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”. Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.
1011HSA.8 – Haws RIVIVEâ„¢ Hydration Stationâ„¢ Chilled Recessed Bottle Filler with HI-LO FountainsModel | 1011HSA.8 |
Material | 14-gauge Type 304 Stainless Steel fountain brackets with the remainder of unit 16-gauge in a satin finish |
Features |
Vandal Resistant
Front access maintenance and filter change
Programable
Smart Energy Savings Mode
Auto purge feature automatically cycles once every 24 hours
|
Dimensions |
Length: 18-5/8″
Width: 38-1/4″
Height: 50″
|
ADA | Yes |
Hygienic Features |
24-Hour Purge of water line
Sensor Operated Bottle Filler
100% lead-free waterways
|
Field Configurable Filtering | Choose between filtered or non-filtered water with the included interchangeable 3000-gallon filter and 5y rated strainer. |
Included Components |
Chiller (HCR8)
Bottle Filler and Fountains
Mounting Frame
Interchangeable filter and strainer
|
Chilling | Refrigeration system is hermetically sealed and delivers a minimum of 8 gph (30.3 L) of water at 50° F (10° C) cooled from 80° F (26.7° C) inlet water at 90° F (32.2° C) ambient. |
Power | 115 Volts, 60Hz, rated watts: 370, full load amps: 5 |
Code Compliance |
ADA
NSF/ANSI/CAN 61- Section 9
CSA Certified
NSF/ANSI/CAN 372
California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100)
NSF/ANSI/CAN 61: Q ≤ 1
|
Mounting | Wall Mounted (In-Wall Frame Included) |
Model 1011HSA.8 barrier-free vandal-resistant electric water cooler and bottle filling station provides 8 gph (30.3 L) chilled drinking water performance in an engineered stainless steel skin. This wall-mounted swirl bowl designed fountain offers the only all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. Outfitted with such protective features as vandal-resistant bubbler heads, waste strainers, and bottom plates, this electric water cooler is quick to discourage vandals. Fountain and bottle filler advantages include:
- The fountains stainless steel valve body is the only one on the market machined from solid bar stock
- 18-gauge Type 304 Stainless Steel bowl assemblies mounted on 14-gauge Type 304 Stainless Steel wall brackets
- Vandal resistant components include the bubblers, bowls, buttons, drains and bottom plates
- Engineered waste plumbing with enough access room for water stop, electrical junction box, filter and drain connections
- LED lighted 12″ sensor operated bottle opening with quick 1.1 gpm fill rate and laminar flow with front access for changing filter
- 3000 gallon (11356 L) capacity, Electronic Lifecycle Control filter cartridge, with filter replacement indicator light. When filter expires, solenoid stops dispensing water to bottle filler
- Smart energy savings feature powers down refrigeration system after 2 hours of non-use and will automatically start again when used
- Auto purge feature automatically cycles once every 24 hours, if no use, to assure a fresh water supply as well as trap integrity
- 100% lead-free waterways
- Display menu which shows sensor range adjustment, factory reset, software/firmware version readout and error readout, along with bottle counter showing number of bottles saved
- Vandal-resistant sensor resists scratching and water droplet fowling, and is separated from display for maintenance.
- Easy maintenance with front fountain access to valve adjustment and cartridge replacement
Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”. Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.
7661 – Hand Wash Sink with AXION Eye/Face WashModel 7661 barrier-free hand wash sink with eye and face wash features the medically acclaimed AXION MSRÂ eye/face wash head assembly. This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain.
- 30″ wide 14-gauge Type 304 Stainless Steel sink mounted on 14 gauge Type 304 Stainless Steel sink supports
- Integral to the sink construction is the seamless 1-1/2″ male NPT drain with 1-1/2″ trap and tailpiece supplied
- Motion-activated faucet operation (operating on 110VAC or battery power) for safety and peace of mind
- Supplied with .5 gpm and 1.2 gpm laminar flow faucet nozzles, with an optional 2.2 gpm laminar flow nozzle available for higher flow applications
- Safety mixing valve included supplies tepid water to the eyewash
- Faucet mixing valve included supplies the faucet with an output temperature range of 90-140F
- Eye/face wash streams provide Zero Vertical Velocityâ„¢ stream engineering with even laminar flow for enhanced comfort, stability and effectiveness
- Rounded sink edges lessen risk of injury and hinder both non-hygienic clutter and water pooling
- Beautiful satin finish resists stains and corrosion
- Easy access to the mixing valve, faucet solenoid valve, plumbing and drain through the large front panel
Certified by CSA to meet the ANSI/ISEA Z358.1 Standard for Emergency Eyewash and Shower Equipment. CSA B125.1, and CSA B45.4 certified. NSF61, ASSE 1017 and ASSE 1070-2015 certified faucet mixing valve.