The Haws model SK3 is a wrap around satin finish stainless steel cane touch skirt for installation on the high unit in some applications that may need to comply with ADA protruding objects guidelines. For use on Models Haws 1011 and H1011 series fountains.
SK3HPS – Fountain SkirtThe Haws model SK3HPS is a wrap around matching high polished finished stainless steel cane touch skirt for installation on the high unit in some applications that may need to comply with ADA protruding objects guidelines. For use on Models 1011HPS and H1011.8HPS.
HCR8.50 – Remote ChillerModel HCR8.50 is a 220 Volt, 50 Hz remote chiller provides 8.0 gallons (30.3 L) per hour of cold water. This remote can provide chilled water to a water to a wide variety of fountains with modern styling. Chiller can be concealed under a counter, between or within walls (check local codes), or high on a wall or column. Ideally suited for factories, cafeterias, restaurants, schools, and offices. Other uses could be for precooling for beverage dispensers and fountains, machine coolant cooling, photo and X-ray processing, laboratory experimental work, or a capacity booster for ice cube makers. Model HCR8.50, 8-gph remote chiller, includes a heavy gauge galvanized steel cabinet.
The refrigeration system is balanced to provide low energy usage and a longer life assured by utilizing a high displacement compressor, a counterflow cooling evaporator/chiller, efficient capillary sizing, a large capacity dryer-strainer, and a fan-cooled condenser with maximum heat exchange. Environmentally friendly refrigerant is controlled by calibrated capillary tube. Air cooled remote chillers require air circulation for proper operation. Any chiller mounted under a counter must also be provided with adequate ventilation.
When chiller is installed in wall be certain that it can always be removed through opening without damaging either chiller or wall. Allow minimum 1″ clearance. Minimum 4″ clearance on back side. Unit is furnished with leads enclosed inside terminal enclosure 220 Volt, 50 Hz, single phase. Capacity is based on ARI standard of rating conditions of 50° F (10° C) drinking water, 80° F (26° C) inlet water, and 90° F (32° C) room temperature.
Multiple-Outlets: HCR8.50 is capable of supplying a maximum of 2 stations (bubbler, glassfiller). Supply line to station should be adequately insulated and no farther than 7 feet (2.12 m) from chiller.
Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and NSF/ANSI/CAN 61: Q ≤ 1.
Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.
MTG.3500 – Mounting PlateThe Haws model MTG.3500 mounting plate with 6″ (15.2 cm) anchors provide an additional amount of anchoring support and is designed to assist in the installation of the heavy-duty series fountains. Specifically to be used in the pedestal models 3500, 3500FR, and 3500D. Set in place during the base concrete pour, this anchored mounting plate allows the fountain to be easily and quickly installed.
- Stainless steel construction with 6″ (15.2 cm) welded zinc anchors provides a solid support system for the pedestal fountain.
The Haws model MTG.3501 anchors with bolts and washers provides an additional amount of support and is designed for use with the heavy-duty line of fountains. Specifically to be used with the 3500 series fountains. Set in place during the base concrete pour, this anchored mounting plate allows the heavy-duty series fountains to be easily and quickly installed.
- Galvanized 6″ (15.2 cm) steel anchors along with 5/8″ x 1-1/2″ (1.6 x 3.8 cm) stainless steel bolts and washers provide a solid support system for the pedestal fountains.
The Haws model MTGFR.17 in-wall mounting frame provides the maximum support and facilitates for the installation of single height electric drinking fountains. Mounted during rough-in phase of construction, this mounting frame allows the H1117.8 fountain to be easily and quickly installed.
- One-piece 10 gauge heavy duty mounting plate is welded to the 16 gauge wall frame
- Heavy gauge galvanized steel construction provides a solid support system for this dual bubbler fountain that is not only sturdy bu provides corrosion resistance as well.
- Wall opening size required is 31-1/8″ wide, 36-1/4″ high, and 12″ deep (79.1 x 92.1 x 30.5 cm).
The Haws model MTGFR.7 in-wall mounting frame provides the maximum support and facilitates for the installation of single height electric drinking fountains. Mounted during “rough-in” phase of construction, this mounting frame allows the H1107.8 fountain to be easily and quickly installed.
- One-piece 10 gauge heavy duty mounting plate is welded to the 16 gauge wall frame
- Heavy gauge galvanized steel construction provides a solid support system for the single bubbler fountain that is not only sturdy but provides corrosion resistance as well.
- Wall opening size required is 14″ wide, 25-13/16″ high, and 12″ deep (35.6 x 65.6 x 30.5 cm).
Model MTGFR.DF1 in-wall mounting frame provides the maximum support and facilitates the installation of single bubbler ‘swirl bowl’ series fountains. Mounted during “rough-in” phase of construction, this mounting frame allows the single bubbler fountains to be easily and quickly installed.
- One-piece 10 gauge heavy duty mounting plate is welded to the 16 gauge wall frame
- Heavy gauge galvanized steel construction provides a solid support system for these single bubbler fountains that is not only sturdy but provides corrosion resistance as well.
- Wall opening size required is 14-1/8″ wide, 15-5/8″ high, and 2″ deep (35.9 x 39.4 x 5 cm)
Model MTGFR.DF2 in-wall mounting frame provides the maximum support and facilitates the installation of “Hi-Lo” 1011MS and 1011HPSMS series fountains. Mounted during “rough-in” phase of construction, this mounting frame allows the “Hi-Lo’ fountains to be easily and quickly installed.
- One-piece 10 gauge heavy duty mounting plate is welded to the 16 gauge wall frame
- Heavy gauge galvanized steel construction provides a solid support system for these dual bubbler fountains that is not only sturdy but provides a certain amount of corrosion resistance as well.
Model MTGFR.LG in-wall mounting frame provides the maximum support and facilitates the installation of “Hi-Lo” electric drinking fountains. Mounted during “rough-in” phase of construction, this mounting frame allows the hi-lo fountains to be easily and quickly installed.
- One-piece 10 gauge heavy duty mounting plate is welded to the 16 gauge wall frame
- Mounting frame provides a solid support system for the dual bubbler fountains that is not only sturdy but provides corrosion resistance as well
- Wall opening size required is 31-1/8″ wide, 37-5/8″ high, and 12″ deep (79.1 x 95.6 x 30.5 cm)
Model MTGFR.SM in-wall mounting frame provides the maximum support and facilitates for the installation of single height electric drinking fountains. Mounted during rough-in phase of construction, this mounting frame allows for many single bubbler fountains to be easily and quickly installed.
- One-piece 10 gauge heavy duty mounting plate is welded to the 16 gauge wall frame
- Heavy-gauge galvanized steel construction provides a solid support system for these dual bubbler fountains that is not only sturdy but provides corrosion resistance as well
- Wall opening size required is 14-1/8″ wide, 32-1/8″ high, and 12″ deep (35.9 x 81.6 x 30.5 cm)
The Haws model PA3177, stainless steel access plate for main pedestal. Dimensions are 8-3/8″ wide x 12-1/4″ high.
