The newly retooled Haws 7501 compact portable eyewash is a 9-gallon (34.1 L) capacity gravity operated portable eyewash that supplies a continuous flow of water for a full 15 minutes at .4 gpm. This unit is a cost-effective solution ideal for locations without access to potable water, including temporary decontamination sites, temporary treatment facilities, and short-term job sites.

Product enhancements include:

• Featuring a FDA approved high-density green polyethylene tank that is easily activated by pulling the yellow activation arm down to the open position
• A wide-fill opening with a securely threaded cap, and a pronounced ‘Max Fill’ line permits easy inspection, cleaning and filling
• Relocation is simple due to ‘Lift Here’ graphics, easily mounted bracket (included) and light design of this 9-gallon (34.1 L) portable
• Measurements: 14-1/2″ high, 22″ wide, 10-1/8″ (36.8 x 55.9 x 25.7 cm) deep. *Note: Unit must be wall hung

Certified by CSA to meet the ANSI/ISEA Z358.1 Standard for Emergency Eyewash and Shower Equipment. This is clearly called out on the exterior of the unit.

The newly retooled Haws 7501T compact portable tempered eyewash ideal for remote locations. The 9-gallon (34 L), gravity-fed, eyewash uses a heated, insulated blanket to provide ANSI compliant tempered potable water in operating temperatures between -20° F (-30° C) and 100° F (38° C) for locations without access to a continuous potable water source. 120VAC, 60Hz, 1.38A electrical requirement with supplied 8′ power cord. This unit is a cost-effective solution ideal for locations without access to potable water, including temporary decontamination sites, temporary treatment facilities, and short-term job sites.

• A wide-fill opening with a securely threaded cap, and a pronounced “Max Fill” line that permits easy inspection, cleaning and filling
• FDA approved high-density green polyethylene tank that is easily activated by pulling the yellow activation arm down to the open position
• Ease of relocation due to “Lift Here” graphics, easily mounted bracket (included) and light design
• Measurements: 16″ high, 24″ wide, 12″ deep (36.8 x 55.9 x 25.7 cm). *Note: Unit must be wall hung

QPS-C-US-Certified-Electrical-Safety for NEMA/Type 3R in ordinary locations, and to ANSI/ISEA Z358.1 Standard for Emergency Eyewash and Shower Equipment, which is clearly called out on the exterior of the unit.

Deck mounted sink units like the 4110ADA are installed in accessible countertop locations for quick locating and convenient operation. Sunken down sink design with water tight fit and stainless steel mounting rim helps to minimize excess splashing, keeping the drinking area contained.

• White acid-resistant enameled iron sink makes for one of the toughest mounting surfaces Haws produces
• Measurements are 24″ x 16″ x 5″ (61 x 40.6 x 12.7 cm)
• Mounted at the correct height and equipped with proper drinking fountain and faucet, this unit complies with the Americans with Disabilities Act requirements for drinking fountains

Specify one of the following gooseneck faucets to be installed left rear side:

Model 5510LF stay-open lever handle, polished chrome-plated brass gooseneck faucet,

Model 5452LF, self-closing lever handle polished chrome-plated brass gooseneck faucet, or

Model 5530LF stay-open, hot and cold lever handle, polished chrome-plated brass gooseneck faucet.

Specify the following bubbler to be installed on right front side;

Model 5054LF lever handle polished chrome-plated brass drinking faucet,

Model 5017LF push button polished chrome-plated brass drinking faucet with renewable cartridge and vandal resistant lock pin, or

Model 5051LF self-closing lever handle drinking faucet with a polished chrome-plated brass finish, adjustable stream flow, and vandal resistant lock pin.

Deck-mounted sink units like the 4210 are installed in accessible countertop locations for quick locating and convenient operation. Sunken down sink design helps to minimize excess splashing and self-rimming feature allows for easy mounting.

• Stainless steel construction offers a good amount of durability and corrosion resistance
• Beautiful satin finish resists stains and corrosion
• Sitting watertight along with sound deadening underneath keep this unit mounted securely on any countertop
• Measurements are 25″ x 17″ x 5″ (63.5 x 43.2 x 12.7 cm)
• Mounted at the correct height and equipped with proper drinking fountain and faucet, this unit complies with the Americans with Disabilities Act requirements for drinking fountains

Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, Section 9, California Proposition 65, and the Federal Safe Drinking Water Act.

Specify one of the following gooseneck faucets to be installed left rear side:

Model 5510LF stay-open lever handle, polished chrome-plated brass gooseneck faucet,

Model 5452LF self-closing lever handle polished chrome-plated brass gooseneck faucet or,

Model 5530LF stay-open, hot and cold lever handle, polished chrome-plated brass gooseneck faucet.

Specify the following bubbler to be installed on right front side:

Model 5054LF lever handle polished chrome-plated brass drinking faucet,

Model 5017LF push button polished chrome-plated brass drinking faucet with renewable cartridge and vandal resistant lock pin, or

Model 5051LF self-closing lever handle drinking faucet with a polished chrome-plated brass finish, adjustable stream flow, and vandal resistant lock pin.

Deck-mounted sink units like the 4230 are installed in accessible countertop locations for quick locating and convenient operation. Sunken down sink design helps to minimize excess splashing and self-rimming feature allows for easy mounting.

• Stainless steel construction offers a good amount of durability and corrosion resistance
• Beautiful satin finish resists stains and corrosion
• Sitting watertight along with sound deadening underneath keep this unit mounted securely on any countertop
• Measurements are 31″ x 19″ x 5″ (78.7 x 48.2 x 12.7 cm)
• Mounted at the correct height and equipped with proper drinking fountain and faucet, this unit complies with the Americans with Disabilities Act requirements for drinking fountains

Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, Section 9, California Proposition 65, and the Federal Safe Drinking Water Act.

Specify one of the following gooseneck faucets to be installed left rear side:

Model 5510LF stay-open lever handle, polished chrome-plated brass gooseneck faucet.

Model 5452LF self-closing lever handle polished chrome-plated brass gooseneck faucet or,

Model 5530LF stay-open, hot and cold lever handle, polished chrome-plated brass gooseneck faucet.

Specify the following bubbler to be installed on right front side:

Model 5054LF lever handle polished chrome-plated brass drinking faucet.

Model 5017LF push button polished chrome-plated brass drinking faucet with renewable cartridge and vandal resistant lock pin, or

Model 5051LF self-closing lever handle drinking faucet with a polished chrome-plated brass finish, adjustable stream flow, and vandal resistant lock pin.

Haws 3377BFFR vandal-resistant bottle filler attachment for the 3377FR pedestal drinking fountain uses a freeze-resistant valve assembly to provide year round operation. Equipped with vandal resistant components, this fountain is not easily disrupted, quickly discouraging vandals. A 3/16″ (.47 cm) galvanized steel extension with green powder-coated finish provides exceptional corrosion resistance.

• Vandal resistant components include the button and bottom/access plates

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

The Haws 3377FR ADA outdoor vandal-resistant powder-coated pedestal and stainless steel fountain incorporates a freeze-resistant valve assembly to provide year round operation. Fully engineered pneumatic valve assembly is one of the best in freeze-resistant technologies. The barrier-free design of the 3377FR allows the square pedestal to be placed securely in multiple locations without taking up excess space. Equipped with vandal resistant components, this fountain is not easily disrupted, quickly discouraging the worst of vandals.

• 14 gauge stainless steel bracket; with 3/16″ (.47 cm) galvanized steel pedestal with green powder-coated finish provide exceptional corrosion resistance
• Vandal resistant components include the bubbler, button, bowl, drain and bottom/access plates
• Consult with the local authority having jurisdiction before installation in order to determine if any additional regulations or requirements may apply

Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

Haws pedestal drinking fountains, like the 3482, use a lever handle valve assembly with screwdriver adjustments stream control. Pipe mounted pedestal design allows the 3482 to be placed in multiple locations without taking up excess space. Equipped with vandal resistant components like the pinned bubbler head aligned with basins vandal resistant mounting slots, and waste strainer keep this fountain protected.

• Galvanized pipe with corrosion resistant stainless steel bowl keep this fountain standing with just the right amount of corrosion resistance

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

Model 1920HPS vandal-resistant polished stainless steel bottle filler uses a patented stainless steel push-button valve assembly allowing for front access stream adjustment as well as cartridge and strainer access. This wall mounted bottle filler offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. It can be a stand-alone station, or mounted above the Haws 1001HPS and 1011HPS series drinking fountains.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include the button and bottom plate
• 1 gpm (3.78 L) Laminar flow
• High polished stainless steel finish
• Maintenance is made easy with front access to valve adjustment and cartridge replacement
• This product requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”

Model 1920W vandal-resistant painted white stainless steel bottle filler uses a patented stainless steel push-button valve assembly allowing for front access stream adjustment as well as cartridge and strainer access. This wall mounted bottle filler offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. It can be a stand-alone station, or mounted above the Haws 1311 or 1501 drinking fountains.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include the button and bottom plate
• Painted white finish
• Available steel wall mounting plate recommended
• 1 gpm (3.78 L) Laminar flow
• Maintenance is made easy with front access to valve adjustment and cartridge replacement
• This product requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

The model 2000S Hydration Station bottle filler is a touch-free, hygienic, water dispenser that allows users to enjoy the benefits of fresh, filtered water with none of the drawbacks of bottled water.

Recessed, in-wall-mounted design allows the bottle filling station to be placed securely in multiple locations without taking up excess space. The unit conveniently mounts between standard 16″ (406 mm) studs and is practical for permanent, high-traffic applications such as schools, office buildings, fitness centers, and manufacturing facilities.

Features and Benefits

• Tested and certified by CSA against  NSF/ANSI/CAN 61, Section 9, NSF/ANSI/CAN 372, CSA Standard B483.1 and California Health and Safety Code 116875 (AB 1953-2006)
• Haws logo panel can be replaced with an optional custom printed logo panel
• Manufactured to comply with the American with Disabilities Act when installed per requirements of the Accessibility Guidelines, Section 41.5 for Drinking Fountains & Water Coolers
• ABS front panel is equipped with a hidden lock for easy access
• Sensor features a 30-second timeout function which prevents unwanted use
• Auto purge feature automatically cycles once every 24 hours to assure a fresh water supply as well as trap integrity
• State-of-the-art integral water filtration system assures fresh, filtered water
• 2,500 gallon (9464 L) capacity, Electronic Lifecycle Control filter cartridge, with filter replacement indicator light to notify when replacement is necessary, model 6423
• 16 gauge, Type 304 Stainless Steel back panel
• Laminar flow prevents splashing, keeping the drinking area contained and clean
• #4 satin finish back panel resists stains and corrosion
• Intended for indoor use only

The Haws 3060 vandal-resistant outdoor concrete pedestal drinking fountain incorporates a patented stainless steel push-button valve assembly allowing for front access stream adjustment as well as cartridge and strainer access. This pedestal mounted fountain offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. Equipped with vandal resistant components, this fountain is not easily disrupted, quickly discouraging the worst of vandals.

• Only stainless steel valve body that is machined out of solid bar stock
• Concrete with exposed aggregate finish and wire to reinforce the casting offers an extremely solid and highly protected fountain
• Vandal resistant components include the bubbler, button, drain and access plate
• Easy maintenance with front access to valve adjustment and cartridge replacement
• 100% lead-free waterways
• Hood extension protects the bubbler head with a partial enclosure, for a greater protected drinking point
• Simplistic Portland Gray cement creates just the right amount of appeal for an outdoor fountain
• Consult with the local authority having jurisdiction before installation in order to determine if any additional regulations or requirements may apply
• Concrete Color Options

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

Trouble viewing this website?

Without an up-to-date browser, you may have trouble with some of our features.

Update Now

Edge

Firefox

Chrome