The Haws 8606SS walk-through booth enclosed combination shower and eye/face wash features the medically acclaimed AXION MSR eye/face wash head assembly. This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eye washes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain. AXION MSRÂ also offers a new hydrodynamic shower design that minimizes the strong physical pressure that drives the water to the outer rim of normal showerheads, making the distribution equal across the entire footprint of the flow. Better use of the water flowing through the shower makes it more effective while providing a more comfortable environment by breaking the streams of water into smaller individual droplets.
- Type 304 Stainless Steel dual-entry walk-through booth and piping construction with a satin finish
- Integral center location drain strainer
- Install flexibility with top or bottom inlet supply
- Large universal labeling and signage for easy locating
- Eyewash streams provide Zero Vertical Velocityâ„¢ stream engineering with even laminar flow for enhanced comfort, stability and effectiveness
- A great addition to unsafe environments where the eyes, face, and body may be exposed to corrosive materials
- Requires minimal maintenance and is equipped with test card to record weekly testing
- Reducing installation time, the entire unit is pre-built and fully pressure tested
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment.
8605SS – AXION® MSR Stainless Steel Booth Enclosed Shower and Eye/Face WashThe Haws 8605SS booth enclosed combination shower and eye/face wash features the medically acclaimed AXION MSR eye/face wash head assembly (patent pending). This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eye washes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain. AXION MSR also offers a new hydrodynamic shower design that minimizes the strong physical pressure that drives the water to the outer rim of normal showerheads, making the distribution equal across the entire footprint of the flow. Better use of the water flowing through the shower makes it more effective while providing a more comfortable environment by breaking the streams of water into smaller individual droplets.
- Type 304 Stainless Steel booth and piping construction with a satin finish
- Integral center location drain strainer
- Install flexibility with top or bottom inlet supply
- Large universal labeling and signage for easy locating
- Eyewash streams provide Zero Vertical Velocityâ„¢ stream engineering with even laminar flow for enhanced comfort, stability and effectiveness
- A great addition to unsafe environments where the eyes, face, and body may be exposed to corrosive materials
- Requires minimal maintenance and is equipped with test card to record weekly testing
- Reducing installation time, the entire unit is pre-built and fully pressure tested
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment.
7661 – Hand Wash Sink with AXION Eye/Face WashModel 7661 barrier-free hand wash sink with eye and face wash features the medically acclaimed AXION MSRÂ eye/face wash head assembly. This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain.
- 30″ wide 14-gauge Type 304 Stainless Steel sink mounted on 14 gauge Type 304 Stainless Steel sink supports
- Integral to the sink construction is the seamless 1-1/2″ male NPT drain with 1-1/2″ trap and tailpiece supplied
- Motion-activated faucet operation (operating on 110VAC or battery power) for safety and peace of mind
- Supplied with .5 gpm and 1.2 gpm laminar flow faucet nozzles, with an optional 2.2 gpm laminar flow nozzle available for higher flow applications
- Mixing valve included supplies tepid water to the eyewash and faucet, needing only single set of hot and cold water supply lines
- Eye/face wash streams provide Zero Vertical Velocityâ„¢ stream engineering with even laminar flow for enhanced comfort, stability and effectiveness
- Rounded sink edges lessen risk of injury and hinder both non-hygienic clutter and water pooling
- Beautiful satin finish resists stains and corrosion
- Easy access to the mixing valve, faucet solenoid valve, plumbing and drain through the large front panel
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment. CSA B125.1, and CSA B45.4 certified.
7660 – Hand Wash Sink with AXION Eye/Face WashModel 7660 barrier-free eye wash sink with eye and face wash features the medically acclaimed AXION MSR eye/face wash head assembly. This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain.
- 24″ wide 14-gauge Type 304 Stainless Steel sink mounted on 14 gauge Type 304 Stainless Steel sink supports
- Integral to the sink construction is the seamless 1-1/2″ male NPT drain with 1-1/2″ trap and tailpiece supplied
- Motion-activated faucet operation (operating on 110VAC or battery power) for safety and peace of mind
- Supplied with .5 gpm and 1.2 gpm laminar flow faucet nozzles, with an optional 2.2 gpm laminar flow nozzle available for higher flow applications
- Single mixing valve included supplies tepid water to the eyewash and faucet, needing only single set of hot and cold water supply lines
- Eye/face wash streams provide Zero Vertical Velocityâ„¢ stream engineering with even laminar flow for enhanced comfort, stability and effectiveness
- Rounded sink edges lessen risk of injury and hinder both non-hygienic clutter and water pooling
- Beautiful satin finish resists stains and corrosion
- Easy access to the mixing valve, faucet batteries, plumbing and drain through the large front panel
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment. CSA B125.1, and CSA B45.4 certified.Â
TWBS.SHE – Thermostatic Mixing ValveModel TWBS.SHE, low-lead Emergency Valve (patent pending), thermostatically mixes hot and cold water to provide a safe fluid supply for emergency shower and eyewash equipment. The valve contains a secondary high temperature limit valve to provide additional protection to the user in the event of main tempering valve malfunction. Additionally, to ensure a fail-safe water supply for emergency shower and eyewash stations, a series of cold water by-pass valves open in the event of hot water pressure loss. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate temperature measurement.)
- A flow rate of 1 to 74 gpm (280 L) for better temperature control across the operating range
- AXION’s superior design and technology provide a complete safety solution for increased victim comfort.
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (68% of rated tepid flow rate)
- Low-lead brass valve design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates valve binding
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85° F (29° C)
- Tempered water: High temperature limit is factory set to 87° F (30° C)
- Cold water by-pass valves are closed during normal operation, regardless of flow rate
- For important installation information, please read Scald Warning.
Listings: CSA certified per ASSE 1071, ANSI Z358.1, applicable sections of CSA B125.3, NSF/ANSI 372, NSF/ANSI 61-section 8, California Health and Safety Code 116875 (AB 1953).
TWBS.HF – Thermostatic Mixing ValveModel TWBS.HF, low-lead Emergency Valve (patent pending), thermostatically mixes hot and cold water to provide a safe fluid supply for emergency shower and eyewash equipment. The valve contains a secondary high temperature limit valve to provide additional protection to the user in the event of main tempering valve malfunction. Additionally, to ensure a fail-safe water supply for emergency shower and eyewash stations, a pressure sensing diverter valve is provided that sends a pressure signal to open the cold water by-pass valve in the event of hot water pressure loss, main valve thermostat malfunction, or clogged cold water check-stop. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate temperature measurement.)
- A flow rate of 1 to 78 gpm (295 L) for better temperature control across the operating range
- AXION’s superior design and technology provide a complete safety solution for increased victim comfort
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (100% of rated tepid flow rate)
- Low-lead brass valve design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates valve sticking
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85° F (29° C)
- Tempered water: High temperature limit is factory set to 87° F (30° C)
- Cold water by-pass valves are closed during normal operation, regardless of flow rate
- For important installation information, please read Scald Warning.
Listings: CSA certified per ASSE 1071, ANSI Z358.1, applicable sections of CSA B125.3, NSF/ANSI 372, NSF/ANSI 61-section 8, California Health and Safety Code 116875 (AB 1953).
TWBS.EWE – Thermostatic Mixing ValveModel TWBS.EWE, low-lead Emergency Valve (patent pending) thermostatically mixes hot and cold water to provide a safe fluid supply for emergency eyewash equipment. The valve contains a secondary high temperature limit valve to provide additional protection to the user in the event of main tempering valve malfunction. Additionally, to ensure a fail-safe water supply for emergency shower and eyewash stations, a series of cold water by-pass valves open in the event of hot water pressure loss. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate temperature measurement.)
- A flow rate of 1 to 12 gpm (3.8 to 45.4 L) for better temperature control across the operating range
- AXION’s superior design and technology provide a complete safety solution for increased victim comfort
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (83% of rated tepid flow rate)
- Low-lead brass valve design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates valve binding
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85° F (29° C)
- Tempered water: High temperature limit is factory set to 87°F (30° C)
- Cold water by-pass valves are closed during normal operation, regardless of flow rate
- For important installation information, please read Scald Warning.
Listings: CSA certified per ASSE 1071, ANSI Z358.1, applicable sections of CSA B125.3, NSF/ANSI 372, NSF/ANSI 61-section 8, California Health and Safety Code 116875 (AB 1953).
9202E – Thermostatic Mixing ValveModel 9202E Emergency Valve (patent pending) thermostatically mixes hot and cold water to provide a safe fluid supply for emergency showers and eyewash equipment. Additionally, to ensure a fail-safe water supply for emergency shower and eyewash stations, a series of cold water by-pass valves open in the event of hot water pressure loss. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate measurement.)
- A flow rate of 1 to 78 gpm (295 L) for better temperature control across the operating range
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (64% of rated tepid flow rate)
- Brass valve design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates valve sticking
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85° F (29° C)
- Tempered water: High temperature limit is factory set to 90° F (32° C)
- Cold water by-pass valves are closed during normal operation, regardless of flow rate
- For important installation information, please read Scald Warning.
CSA Listings: CSA certified per ASSE 1071, ANSI Z358.1 and applicable sections of CSA B125.3.
9201E – Thermostatic Mixing ValveModel 9201E emergency mixing valve (patent pending) thermostatically mixes hot and cold water to provide a safe fluid supply for emergency showers and eyewash equipment. Additionally, to ensure a fail-safe water supply for emergency shower and eyewash stations, a series of cold water by-pass valves open in the event of hot water pressure loss. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate temperature measurement.)
- A flow rate of 1 to 31 gpm (3.8 to 117.3 L) for better temperature control across the operating range
- AXION’s superior design and technology provide a complete safety solution for increased victim comfort.
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (65% of rated tepid flow rate)
- Brass valve design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates valve sticking
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85° F (29° C).
- Tempered water: High temperature limit is factory set to 90° F (32° C).
- Cold water by-pass valves are closed during normal operation, regardless of flow rate.
- For important installation information, please read Scald Warning.
CSA Listings: CSA certified per ASSE 1071, ANSI Z358.1, and applicable sections of CSA B125.3.
9200REC – Recessed CabinetModel 9200REC recessed cabinet is manufactured of 18 gauge Type 304 Stainless Steel, locking door which is supplied with a heavy duty stainless steel piano hinge, and removable upper and lower panels to accommodate any of the Haws Thermostatic Mixing Valves.
(Specific panel kits are offered to match specific Valve – please look under options for valve to be ordered for correct kit)
9200SUR – Surface Mount CabinetModel 9200SUR surface mounted cabinet is manufactured of 18 gauge Type 304 Stainless Steel, locking door which is supplied with a heavy duty stainless steel piano hinge, and removable upper and lower panels to accommodate any of the Haws Thermostatic Mixing Valves.
(Specific panel kits are offered to match specific Valve – please look under options for valve to be ordered for correct kit)
9201EFE – Thermostatic Mixing ValveModel 9201EFE Emergency Thermostatic Mixing Valve (patent pending) thermostatically mixes hot and cold water to provide a safe fluid supply for emergency eyewash equipment. Additionally, to ensure a fail-safe water supply for emergency eyewash stations, a series of cold water by-pass valves open in the event of hot water pressure loss. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate temperature measurement.)
- A flow rate of 1 to 12 gpm (3.8 to 45.4 L) for better temperature control across the operating range
- AXION’s superior design and technology provide a complete safety solution for increased victim comfort.
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (83% of rated tepid flow rate)
- Brass valve design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates Thermostatic Mixing Valve sticking
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85° F (29° C).
- Tempered water: High temperature limit is factory set to 90° F (32° C).
- Cold water by-pass valves are closed during normal operation, regardless of flow rate.
- For important installation information, please read Scald Warning.
CSA Listings: CSA certified per ASSE 1071, ANSI Z358.1 and applicable sections of CSA B125.3.