The Haws AX16 AXION Advantage® eye/face wash system is designed to replace outdated, under-performing or in some cases, non-conforming installed emergency eyewashes with the medically superior AXION® MSR performance. This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain. Eyewash streams provide Zero Vertical Velocity™ stream engineering with even laminar flow for enhanced comfort, stability and effectiveness. System includes the AXION MSR eye/face wash head, the necessary connecting hardware, along with a tape measure, eyewash measuring gauge and written guidelines to assure installation complies with the ANSI Z358.1 standard.
System is designed to replace the eyewash head of some standard laboratory and hose-mounted eyewash stations manufactured by Acorn®, Bradley®, Encon®, Guardian® and Speakman®.
The AXION Advantage system is ANSI compliant when installed correctly based on manufacturer guidelines and when tested against the ANSI Z358.1 checklist included with the product. The materials provided offer complete ANSI compliance tools and instructions. At the current time, ANSI does not regulate product brands, models, or the interchange of product components.9055 – Wall Mounted Emergency Stretcher
The Haws model 9055 is a stretcher with hanger designed for use with the Haws enclosed safety showers. The stretcher is lightweight for easy handling, and strong enough for any situation. Wall mounting bracket is included.9050 – Emergency Shower Safety Kit
Model 9050 emergency shower safety kit provides scissors to remove tainted clothing quickly, soap and a towel to help remove chemicals from the skin, and an emergency blanket and flip flop shoes to exit the shower. The kit is kept in an easy to open wall mounted cabinet located near the emergency shower location.SP156 – Thermostat for 8315 Series Models
Model SP156 is a thermostat for the heat traced cable outdoor Models 8315CTFP and 8315CTFP.220V. It has hermetically sealed contacts. Opens (rising) at 52° F (11° C) and closes (falling) at 42° F (5.6° C).SP158.15 – Freeze Bleed Valve for 8315CTFP
Model SP158.15 fully engineered freeze protection valve is specifically designed for the 8315CTFP and is constructed of a one piece brass body, supplied with a removable cartridge for easy cleaning/maintenance, and inlet plumbing and insulation. Automatic thermal actuator bleed valve opens when internal water temperature falls below 35° F (1.7° C) and closes completely when the water climbs back to 42° F (5.6° C). 1/2″ NPTF inlet and outlet.SP157.15 – Scald Bleed Valve for 8315CTFP
Model SP157.15 is a scald protection bleed valve designed specifically for the 8315CTFP. Recommended for high ambient temperature locations where extreme heat or hot sun might cause internal water overheating. Flushes water through line when internal water temperature reaches 98° F (36.7° C) and closes at 95° F (35° C). Full open temperature is 105° F (40.6° C). 1/2″ NPT inlet and outlet.SP145 – Drench Hose/Valve Assembly for 8315CTFP
The Haws SP145 drench hose is specifically designed for model 8315CTFP combination shower and eyewash. Includes a 4-1/2′ hose, inlet plumbing and insulation.SP121 – Auxiliary Outlet Plumbing for 8315CTFP
Model SP121 auxiliary outlet is specifically designed for the 8315CTFP combination shower and eyewash. The configurable outlet design allows for both the SP145 drench hose and the SP158.8 freeze valve to be mounted at the same time, and/or to permit supply water re-circulation through the shower piping.932X – Water Hammer Arrestor Piping Kit
The Haws 932X water hammer arrestor and piping kit series is designed for use with the Haws 9321, 9326 and 9327 Instantaneous Water Heaters. The kit is supplied with stainless steel piping, 1-1/4″ 316 stainless steel supply valve and Y strainer, lead-free bronze 1-1/4″ pressure regulating valve, and a lead-free brass water hammer arrestor. There are 10 kits available according to the size of arrestor needed, and whether the heater is ordered with or without support legs (refer to the sizing chart below).
Water Hammer Arrestor Sizing Chart
|Pipe Length (header to shower)||Arrestor Size||9326/7 Unit with Legs Kit #||9321/6/7 Unit without Legs Kit #|
|15′ — 30′||C||932X-22||932X-21|
|30′ — 50′||D||932X-32||932X-31|
|50′ — 70′||E||932X-42||932X-41|
|75′ — 90′||F||932X-52||932X-51|
Part 0000087773 is an aerator with housing for Haws eyePOD® with a flow of .5 gpm.0000087801 – eyePOD Nozzle
P/N 0000087801 is a faucet nozzle, 1 gpm (3.8 L) for the AXION® eyePOD®.0012506950 – Flow control
Part Number 0012506950 .25 gpm (.9 L) flow control. Controls water flow rate when flowing pressure is between 30 and 90 psi (2.1 and 6.2 bar) and is for use on Haws portable stainless steel tanks.