PBA6 – Valve Button

The Haws model PBA6 flanged push button assembly is used with push button valve 5874PBF, is made of polished chrome-plated brass, and includes the push button, operator, round locknut, snap ring, and wave washer. This model is used on flush mounted (not recessed) front stainless steel drinking fountain models.

PBA7 – Valve Button

The Haws model PBA7 push button assembly is used with push button valve 5874PB, is made of polished chrome-plated brass, and includes the push button, operator, round locknut, snap ring and wave washer. This model is used on drinking fountains with front recessed push buttons and for drinking fountains with thick walls.

HCR8 – Remote Drinking Fountain Water chiller

The Haws model HCR8 remote chiller provides 8 gallons (30.3 L) per hour of 50° F (10° C) +/- 5° cold water to a wide variety of fountains. This model is rated at 115V, 60Hz, single phase, 5 amp service. It is constructed of heavy-gauge galvanized steel and its compact style can be concealed under a counter, between or within walls (check local codes) or high on a wall or column. There are many other applications including pre-cooling of beverage dispensers, and machine coolant cooling.

Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.

6518.2FR – Freeze-Resistant Bury Valve For Dual Fountain

The Haws 6518.2FR freeze-resistant valve system is a fully-engineered pneumatic operated valve for use on all Haws hi-lo two bubbler freeze-resistant pedestal fountains. The placement of the valve below the frost line allows the system to function when freezing conditions are present at surface level. Its fully accessible design allows for reliable service year round.

Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, Section 9, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006).

6521FR – Freeze Resistant In-Wall Valve

The Haws 6521FR freeze-resistant valve system is a fully engineered pneumatic operated valve for use on all Haws single bubbler wall mounted freeze-resistant fountains. The placement of the valve on an interior wall where the ambient temperature minimum is 50° F (10° C) allows the system to function when freezing conditions are present at the fountain outside the wall. Its fully accessible design allows for reliable service year round.

Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, Section 9, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006).

6433 – Strainer

Model 6433 is a lead-free, celcon Y pattern water strainer with removable 100 mesh screen for easy cleaning. 1/4″ NPT(F) inlet and outlet. 1-7/8″ (4.8 cm) long with strainer arm extending to 2-15/16″ (5.6 cm) overall width.

6455 – Waste Strainer

Model 6455 is a polished stainless steel flat waste strainer with grid, washer locknut and slip joint tailpiece. Flange diameter 4-1/2″ (11.4 cm) fits 3-1/2″ to 4″ (8.9 to 10.2 cm) drain holes; 1/1-2″ O.D. (3.8) slip joint tailpiece is 4″ (10.2 cm) long.

5874PB – Fountain Valve

The Haws 5874PB valve uses a patented stainless steel, push-button activated, valve assembly allowing for front access stream adjustment as well as cartridge and strainer access. Valve and push button come equipped with automatic pressure regulation to allow the valve to function under varying water pressures between 30 – 90 psi (2.1 – 6.2 bar); keeping the stream constant throughout the drinking process. Connection is 1/4″ NPT inlet and outlet. Note: Valve assembly includes: push button assembly, tubing, and spanner wrench. Assembly has been used on most Haws fountains with a recessed valve mount produced after October 3, 2003. Unit replaced Model 5872

 

5874PBF – Fountain valve

The model 5874PBF uses a patented stainless steel, push-button activated, valve assembly allowing for front access stream adjustment as well as cartridge and strainer access. Valve and push button come equipped with automatic pressure regulation to allow the valve to function under varying water pressures between 30 – 90 psi (2.1 – 6.2 bar); keeping the stream constant throughout the drinking process. Connection is 1/4″ NPT inlet and outlet. Note: Valve assembly includes: push button assembly, tubing, and spanner wrench. Assembly has been used on most Haws fountains with a flush mount valve produced after October 3, 2003. Unit replaced Model 5872

 

6252HST – Valve Handle

Model 6252HST is a handle and stem assembly for the 6252EHLF valve and shall include an extended lever handle and handle cap. Completely assembled with all supporting parts, and ready to install on valves 2005 and newer. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006).

5830HST – Valve Handle

5830HST handle and stem assembly is used with the 5830LF valve. Used on models from 2005 and newer. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006).

3482 – Pedestal Fountain

Haws pedestal drinking fountains, like the 3482, use a lever handle valve assembly with screwdriver adjustments stream control. Pipe mounted pedestal design allows the 3482 to be placed in multiple locations without taking up excess space. Equipped with vandal resistant components like the pinned bubbler head aligned with basins vandal resistant mounting slots, and waste strainer keep this fountain protected.

Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, Section 9, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006).